航空发动机静叶联调机构运动分析及优化

针对航空发动机可调静子叶片联调机构运动关系复杂、优化难度大的问题,研究了一种采用图解法和齐次坐标法结合MATLAB软件推导两级联调机构运动方程,并运用遗传算法对两级机构中的关键构件进行联合优化的方法。运用该方法对指定联调机构的两级曲柄可调端长度、可调端与固定端夹角进行了优化求解。得到了最优解,使得第一级摇臂转动角度是第零级摇臂转动角度的2倍，且第一级摇臂转动角速度也是第零级摇臂转动角速度的2倍。      

Plastic wrinkling prediction in thin-walled part forming process:A review

The precision forming of thin-walled components has been urgently needed in aviation and aerospace field. However, the wrinkling induced by the compressive instability is one of the major defects in thin-walled part forming. The initiation and growth of the wrinkles are interac-tively affected by many factors such as stress states, mechanical properties of the material, geometry of the workpiece and boundary conditions. Especially when the forming process involves compli-cated boundary conditions such as multi-dies constrains, the perturbation of clearances between workpiece and dies and the contact conditions changing in time and space, etc., the predication of the wrinkling is further complicated. In this paper, the current prediction methods were summa-rized including the static equilibrium method, the energy method, the initial imperfection method, the eigenvalue buckling analysis method, the static-implicit finite element method and the dynamic-explicit finite element method. Then, a systematical comparison and summary of these methods in terms of their advantages and limitations are presented. By using a combination of explicit FE method, initial imperfection and energy conservation, a hybrid method is recommended to predict plastic wrinkling in thin-walled part forming. Finally, considering the urgent requirements of com-plex thin-walled structures’ part in aviation and aerospace field, the trends and challenges in wrin-kling prediction under complicated boundary conditions are presented.     

DME Interference mitigation for L-DACS1 based on system identification and sparse representation

L-band digital aeronautical communication system 1 (L-DACS1) is a promising candi-date data-link for future air-ground communication, but it is severely interfered by the pulse pairs (PPs) generated by distance measure equipment. A novel PP mitigation approach is proposed in this paper. Firstly, a deformed PP detection (DPPD) method that combines a filter bank, correlation detection, and rescanning is proposed to detect the deformed PPs (DPPs) which are caused by mul-tiple filters in the receiver. Secondly, a finite impulse response (FIR) model is used to approximate the overall characteristic of filters, and then the waveform of DPP can be acquired by the original waveform of PP and the FIR model. Finally, sparse representation is used to estimate the position and amplitude of each DPP, and then reconstruct each DPP. The reconstructed DPPs will be sub-tracted from the contaminated signal to mitigate interference. Numerical experiments show that the bit error rate performance of our approach is about 5 dB better than that of recent works and is closer to interference-free environment.     

不同迎角下脊形前体绕流数值模拟研究

脊形前体有较强的背风涡流场,不同的前体形状对前体涡流场和气动力有很大的影响。本文针对脊形前体飞行器大迎角湍流大分离流动计算的困难,采用IDDES混合湍流模型,以及与之匹配的非定常算法,研究了不同来流迎角下脊形前体的气动特性,以及背风涡非定常演化、破裂的细致流动结构。选取了不同脊形角,以及不同上、下高宽比的脊形前体进行计算。计算结果表明,在迎角较小时,随着迎角的增大,前体主涡会逐渐增强,在迎角较大时,前体主涡破裂;在相同迎角下,脊形角较小时,前体涡较强,涡升力也更大;对于相同脊形角的前体,当上半截面高宽比较小时,前体主涡强度较大,前体涡破裂临界迎角较小,即会提前破裂。     

基于6σ设计的复合推力高速直升机总体参数多目标优化

针对复合推力高速直升机总体设计阶段总体参数的选择问题,提出一种提高可靠性和鲁棒性的基于6σ设计的改进多目标遗传算法优化方法。采用叶素理论和数值积分的方法分析计算了复合推力高速直升机气动及飞行性能,并以此为基础建立了约束函数和初步目标函数模型;将6σ设计融入改进的多目标遗传算法中,构造最终目标函数;在给定有效载荷设计要求下,对复合推力高速直升机总体参数进行了多目标优化设计。该方法获得了所需的Pareto解,优化后的复合推力高速直升机飞行性能相对原机有了较大改善,算例结果表明该方法有效可行。     

eLoran系统ASF网格应用算法研究

ASF网格是提高增强型罗兰（Enhanced Long Range Navigation，eLoran）系统精度的重要方法。根据所在网格四个顶点的附加二次时延（Added Secondary Factor，ASF）值通过网格应用算法得到待测试点的ASF值，一定程度上比公式计算的ASF值更准确。在计算过程中，用户四个顶点ASF值的测量误差会传递给用户，同时内插算法本身也会引入误差，此时内插算法的选择尤为重要。本文通过仿真、分析比较几种常用的内插算法，得出结论：反距离插值算法引入的误差最大，双线应插值算法引入的误差最小，而且误差呈现一定层次感，网格从内到外误差逐渐减小。     

危险天气下航班等待与改航的实时集成优化

为了提高航班准点率,降低危险天气对航班飞行的影响,同时考虑等待策略和改航策略,进行实时空中交通流量管理的研究。以改航起始点至改航结束点间的总航行时长最短为目标,安全可行性、技术可行性为约束,建立了数学模型,并设计了两阶段求解算法,先基于遗传算法优化等待时长和改航路径,再基于"化曲为直"和"二分法"的思想调整改航路径,得到了最佳等待时长和改航路径。仿真结果表明,该算法得到的实时优化结果优于几何切线法;相比静态改航,更能提高空域利用率;相比单独考虑等待策略,总航行时长降低了17.04%;相比单独考虑改航策略,总航行时长降低了3.98%;验证了危险天气下航班等待时长与改航路径实时集成优化在实时空中交通流量管理中的有效性。     

存在干扰下的无人机中继站波束成形算法

无人机(UAV)通信具有部署快、使用灵活、通信质量好等优点,在无线通信领域具有广阔的应用前景。采用UAV作为中继站构成的增强型卫星通信网络经常受到各种干扰的影响,导致其性能急剧下降。以信干噪比(SINR)最大化为准则,UAV中继站发射功率满足要求为约束条件的优化问题的基础上,提出了一种基于最大瑞利熵的波束成形(BF)算法,得出最优权矢量。为了降低BF算法的实现复杂度,进一步提出了一种基于迫零(ZF)的次优BF算法。计算机仿真验证了这2种BF算法的有效性。     

粒子群算法在装配序列规划中的应用方法研究

将粒子群优化算法引入到装配序列规划中,详细讨论了粒子群算法在装配规划中的数学表示,给出了适应度函数评价方法,并实现了装配干涉矩阵的构建,以发动机化油器装配为例,分析了粒子群算法在装配序列规划中的具体应用.     

基于NFTET的高超声速飞行器鲁棒轨迹重构设计

考虑高超声速飞行器故障下安全再入飞行问题，针对飞行器发生较大故障的情况，提出了基于相邻可行轨迹存在定理(Neighboring feasible trajectory existence theorem,NFTET)的鲁棒在线轨迹重构算法。在标称情况下基于反馈线性化预测校正制导算法生成满足各种约束条件的再入轨迹；由于NFTET只适用于发生较小故障的情况，为保证较大故障下飞行器仍能以较高精度安全着陆，基于NFTET理论设计了鲁棒轨迹重构算法，得到了较高落点精度的飞行轨迹。仿真结果表明，本文所提出算法能有效解决飞行器较大故障下的安全再入轨迹重构问题，提高了飞行器的自主容错能力。